- Bridge Mode Connection
- IDAS to Analogue Connection
- Mixing Function
- Analogue/SIP Telephone Interconnect
- Cross Band Connection
- Converter Mode
- Optional Remote Communicator Software (RC-FS10)
- External Equipment Connectors
- Web-Based Configuration
- IP Router Function
- USB Flash Drive Connection (for Firmware Update and Backup)
Versatile Radio Over IP Gateway
The VE-PG3 is designed to enhance the communication coverage of a radio network and the convenience of radio usage by leveraging IP networking technology with ease of implementation.
The VE-PG3 has two modes; converter mode and bridge mode. The converter mode converts radio audio into VoIP/analog phone calls and allows interconnection between connected equipment.
The bridge mode connects two or more radio sites over an IP network and received radio audio is bridged to opposing radio sites of the network. The bridge mode can connect dispersed radio sites over the network and can provide cross band, cross category communication.
The VE-PG3 has built-in RoIP, SIP gateway, IP router and IP PBX functions all in one box. As shown in the above figure, the VE-PG3 integrates digital/analog radio sites into SIP and analog phone systems and interconnects calls between the connected users. The CT-24 digital voice converter converts analog audio and G.711μ IP phone codec to the AMBE+2™ codec for the IDAS™ radio system*. The CT-24 is required to connect an IDAS™ radio site with other system users.
* IDAS™ NXDN™ Type-D multi-site trunking and conventional system using the IC-FR5000 series.
IDAS™ dPMR™ Mode 2 repeaters and UC-FR5000 #12.
A radio user (both IDAS™ and analog* radio user) can initiate phone calls using DTMF code and can connect to other users via an IP phone or PSTN line. Phone users can make individual calling and group calling to the IDAS™ radio site. In the analog radio site, called users are subject to the fixed calling configuration of the connected radio.
* Limited to radios with DTMF encoder/decoder capability.
The bridge mode bridges between radio sites over an IP network. The above figure is an example of bridge mode configuration, the Site A radio user can talk to the Site B radio user.
Site-to-multisite Radio Communication
When the IP network system is compatible with IP multicast routing, three or more VE-PG3s can be connected in the bridge mode and provide site-to-multisite radio communication. As shown in the figure below, the Site A radio users can talk to the Site B and Site C users simultaneously.
The mixing function mixes the bridged audio to the other bridges. It can provide site-to-multisite type communication even on a network which does not support IP multicast routing.
Cross Band/Cross Category Connection*
Cross band/cross category connection is possible between VHF/UHF land mobile, marine VHF and air band frequencies. Optional audio connection cables allow you to connect a transceiver or repeater easily. In addition, the SM-26 or HM-152 can be connected directly to the VE-PG3 via the optional OPC-2276 connection cable.
|*||Cross band/cross category operation may be prohibited in some countries. Please confirm legal requirements in your country before installation.|
Remote Communicator Software, RC-FS10
The optional RC-FS10 remote communicator creates an IP-based virtual radio on a PC and works as simple dispatch station. The RC-FS10 can be used with an IDAS™ NXDN™ system and analog radio system via the VE-PG3.
External Equipment Connection
The VE-PG3 has two external equipment connectors for audio input/output and other switching. Public address system, siren, warning light and other external equipment can be connected to the VE-PG3.
Serial Pass-through Function
The serial pass-through function allows you to remotely control connected equipment from an PC via RS-232C interface. The virtual serial port software is supplied with the VE-PG3.
- IP router function: PPPoE/IPv6 bridge, NAT, Dynamic DNS, VPN pass through, IP filter, SNMP and SYSLOG
- USB flash drive connection for firmware update and data backup and restore
Supplied accessories (May differ according to version)
- AC adapter, BC-207S
- Ferrite core
- Quick connectors (Spare)
- Virtual serial port software CD
Rear panel view